Splined hub, six-bolt rotor: what you need and how it goes on
Splines where the rotor mounts mean a Center Lock hub, and a six-bolt rotor won't bolt to it. This page shows how to confirm your hub's mount, which rotors and adapters their makers list, and the published steps and torque figures for fitting them.
The short answer
Splines where the rotor goes mean a Center Lock hub. It takes a rotor with a splined center, held by a threaded lockring, so a six-bolt rotor has nothing to bolt to. You have two ways forward:
- Buy a Center Lock rotor the same diameter as your current one, in a thickness your brake's manual approves, listed for your brake pads, with a lockring that suits your hub.
- Keep the six-bolt rotor and add a Center Lock adapter whose maker names your rotor, or gives limits your rotor meets, and lists your axle.
Park Tool's rotor guide says a six-bolt rotor can go on a Center Lock hub with an adapter kit made for it, and that the reverse is not possible. So the hub sets the mount, and the rotor side is what you change: a different rotor, or an adapter under the one you have.
Fit it the way the makers specify:
- Rotor arrow pointing the way the wheel turns forward.
- Lockring to 40 N·m. Shimano, Magura, TRP, HED and DT Swiss (for its adapter) give that figure; Zipp gives 40 N·m as its maximum.
- Bolts prepared the way the rotor maker says. Magura and Zipp call for new bolts with fresh threadlocker; Shimano lists its six-bolt rotors with an anti-loosening plate, so follow that rotor's own instructions.
- Bolts tightened crosswise to the rotor maker's figure. Into an adapter, don't go over the adapter maker's figure (TRP gives 4–6 N·m). Into a six-bolt hub, stay within the hub maker's maximum.
Which mount does your hub have?
- Six-bolt (Zipp's term is ISO 6-bolt): six threaded holes in a circle on the hub. Magura says the rotor's holes must sit exactly over them.
- Center Lock: a splined collar with a thread for the lockring. Zipp's manual slides the rotor onto the hub splines, then threads the lockring into the hub. Park Tool notes that lockrings have notches either outside or inside.
- Eight-bolt: Magura's MDR-S 8H 203 needs special flat-head bolts, tightened to the hub maker's specification.
The spec sheet settles it. Shimano's 2026-2027 Spec. Handbook gives its disc hubs a "Brake type" row. In the Front Hub (Disc Brake) table on printed page 200 (page 203 of the PDF), the HB-QB400 is "6-bolt disc brake", while the HB-QC400 beside it is "CENTER LOCK disc brake". Zipp's Wheel and Hub Specifications list its ZM2 hubs as 6 Bolt and its ZM2 SL hubs as Center Lock, and its wheel tables carry a "Brake Compatibility" row. Similar names can hide different mounts, so look up your exact model.
Option 1: a Center Lock rotor
Four things have to match: the diameter your caliper is set up for, a thickness your brake's manual approves, your brake pads, and a lockring that fits your hub. Magura's rotor instructions put the thickness rule plainly: use only a thickness approved for your brake in its user manual. For Shimano rotors, the Rotor (CENTER LOCK) table on printed page 244 of the handbook (page 247 of the PDF) lists diameters, thickness and pad compatibility:
- Thickness: every Shimano Center Lock rotor there is the standard 1.75 mm except the RT-CL750, which is 2.2 mm. Shimano's chart C-461 lists the 2.2 mm rotors for four calipers: BR-M9220, BR-M8220, BR-M6220 and BR-MT620.
- Pad material: RT-CL300, SM-RT54, SM-RT30 and SM-RT10 are listed for resin pads only. The notes to chart C-461 say these rotors will be easily damaged if used with metal pads.
- Pad lining shape: RT-CL900, RT-CL800, RT-CL700, RT-CL750, SM-RT900, SM-RT800 and SM-RT64 are listed for narrow linings only; RT-CL300, SM-RT54, SM-RT30 and SM-RT10 for narrow or wide.
With a Shimano brake, chart C-461 in Shimano's compatibility PDF (printed pages 59 to 62, pages 54 to 57 of the file) is where to look: it lists the rotors each caliper takes, by diameter, with footnotes on size limits.
Which lockring fits is set by the hub. Shimano's chart C-612 (printed page 63 of the compatibility PDF, page 58 of the file) gives the rule for its hubs:
- Front hubs, internal-spline lockring: quick-release and 12 mm E-THRU hubs, not 15 mm E-THRU or 20 mm thru-axle hubs.
- Front hubs, external-spline lockring: all four types.
- Front hubs, internal-and-external type: all four, but on an E-THRU hub tighten it with TL-FC36, because TL-LR11 cannot install it.
- Rear hubs go by model, not axle. FH-M9111, FH-M9111-B, FH-M9111-BS, FH-M9000, FH-M9010, FH-M9010-B, FH-MT901-B and FH-MT901-BS take only the external-spline lockring. Shimano's other rear disc hubs take all three types.
For front hubs, TRP's guide draws the line in the same place: a lockring with 12 internal notches for 12 mm axles, one with 16 external notches for 15 and 20 mm axles. On a rear wheel, find your hub model in chart C-612 before choosing a lockring. Shimano's dealer's manual DM-MADBR01 names TL-LR15 with an adjustable wrench for the internal type and TL-FC36 for the external type. Park Tool matches a BBT-9, BBT-69.4 or similar to outside notches and its FR-5.2 family to inside-only notches. TRP calls for a cassette installation tool on the internal type, the kind that fits a cassette lockring. Unsure of your axle size? See replacing a thru axle.
Option 2: an adapter for the six-bolt rotor
Park Tool describes two designs. On a Shimano-style adapter the rotor bolts to the adapter, then a lockring goes on; on a DT Swiss-style adapter the rotor sits on six fittings and the lockring clamps it. Only some makers say which rotors their adapter takes. Shimano and Magura name models, and DT Swiss gives thickness and diameter limits. The others describe their fit in general terms, so if your rotor isn't named, check your rotor maker's instructions before relying on one of them.
| Adapter | Rotors its maker names | Axles and other limits |
|---|---|---|
| Shimano SM-RTAD05 | SM-RT66, SM-RT56 and SM-RT26. Not the SM-RT86, the six-bolt rotor installed with an aluminum adapter. | Front: 9 mm quick release, 15 mm E-THRU, 20 mm thru. Rear: 10 mm quick release, 10 mm thru, 12 mm thru, 12 mm E-THRU. Hexalobular rotor bolts; steel external-serration lockring. |
| Magura Centerlock adapter | Magura STORM, STORM HC, STORM SL 2, MDR C and MDR S. Never MDR P. | Rotors up to 203 mm. Never with ABS sensor rings. Use the Magura lockring for your axle type (quick release or thru axle). |
| DT Swiss CL-Adapter (MTB; ROAD for QR/TA9/TA12; Hybrid with magnet) | No model list. Rotors 1.8 to 2.2 mm thick. | Up to the diameter marked on its lockring. Complete assembly only. Lockring 40 N·m. |
| TRP Centerlock to 6-Bolt Adapter (ABOT001215) | No list. TRP says it suits most six-bolt rotors and to confirm fit with your hub and rotor makers. | 12 mm or 15–20 mm versions. Rotors up to 223 mm. Rotor bolts 4–6 N·m; lockring 40 N·m. |
| HED 6-Bolt to Centerlock Adapter with Lockring | No list. HED says any six-bolt rotor. | 12, 15 and 20 mm thru axles and quick release. Lockring included; 40 N·m. |
| HUNT 6-Bolt Rotor Adapter | No list. HUNT says the majority of six-bolt rotors. | For the Center Lock spline on HUNT disc hubs. Rotors up to 180 mm. Lockring included. |
| Ritchey hub adapter center-lock to 6 bolt w/lockring | Not stated. | Quick release/12 mm and 15/20 mm thru-axle versions. Lockring included. |
Magura MT A2 brakes: Magura's MT A2 instructions say never to use the six-bolt MDR-A rotor with a Center Lock adapter, whether Magura's own or another maker's. The same instructions say to use only genuine Magura rotors designed for the MT A2, and name the MDR-A and MDR-A CL.
Other exclusions are easy to miss:
- Shimano says the SM-RTAD05 cannot be used with the SM-RT86.
- With a Magura brake, Magura's rotor instructions say to use only Magura original parts, adapters and bolts included.
- Shimano lists the SM-RT66, SM-RT56 and SM-RT26 at 1.75 mm thick, below the 1.8 mm minimum DT Swiss gives for its adapter.
- On one of the Shimano rear hubs that take only the external-spline lockring, check the adapter's lockring type. Shimano lists the SM-RTAD05 with an external-serration lockring. TRP pairs 12 mm axles with its internal-notch lockring, so on those hubs confirm fit with TRP before choosing its 12 mm version.
How it goes on
| Document | Lockring | Rotor bolts |
|---|---|---|
| Shimano dealer's manual DM-MADBR01 (hydraulic disc brake) | 40 N·m | Not covered; the section is for Center Lock rotors |
| Magura disc brake rotor assembly instructions | 40 N·m (354 lbf-in) | 6 N·m (53 lbf-in); MDR-S 8H 203: hub maker's figure |
| DT Swiss hubs user manual V2026.05 | 40 N·m (its Center Lock adapter) | 6 N·m |
| Zipp road wheels user manual | 40 N·m (354 in-lb) maximum | Rotor maker's figure, 6.2 N·m (55 in-lb) maximum |
| TRP six-bolt to CenterLock adapter guide | 40 N·m | 4–6 N·m, into the adapter |
- Clean the hub splines and lockring thread, as DT Swiss's steps begin; TRP wipes the hub's mounting surface with isopropyl alcohol. Keep grease off: Park Tool says not to grease or oil rotor bolts, and that grease isn't needed on Center Lock rotors and may contaminate the rotor surface.
- Assemble any adapter in the order its instructions give, and fit the rotor with its direction arrow pointing the way the wheel turns forward.
- Bolted rotor: prepare the bolts the way the rotor maker says. Magura calls for new bolts with fresh medium-strength threadlocker, and Zipp for new, threadlock-prepped bolts. Shimano lists its six-bolt rotors with an anti-loosening tightening plate, so follow that rotor's own instructions. Magura's sequence: two or three turns by hand, rotor turned against the direction of rotation as far as it goes, then tighten crosswise.
- Torque the bolts to the rotor maker's figure. Into an adapter, don't go over the adapter maker's figure: TRP gives 4–6 N·m, and Park Tool says to torque bolts into a Shimano-style adapter as you would on a six-bolt hub, where it puts typical torque at about 4–6 N·m. Into a six-bolt hub, never go above the hub maker's maximum (Magura's MT A2 instructions).
- Clamp-type adapter: use all its parts together, as DT Swiss requires for its adapter. On Magura's adapter, the six hooks of the spring washer must noticeably engage the adapter.
- Thread the lockring on by hand, then tighten to 40 N·m with the tool that fits its notches.
- Degrease the rotor with brake cleaner or alcohol (Magura); Park Tool and TRP use isopropyl alcohol. Magura says a new rotor gets new pads.
- Bed in with your brake maker's procedure. Magura's rotor instructions: repeated slowdowns from 20 km/h (12 mph) to 5 km/h (3 mph), one brake at a time, until braking stops improving.
If it rubbed or the bolts loosened
We can't see your wheel, so this is not a diagnosis. These are the checks the makers' documents point to:
- Combination: is the rotor one the adapter's maker names, within its diameter limit and, for DT Swiss, 1.8 to 2.2 mm thick? A six-bolt Magura MDR-A goes on no Center Lock adapter at all.
- Rotor and caliper: the notes to Shimano's chart C-461 say narrow-type two-piece rotors are not compatible with calipers made for wide-type rotors, because of interference.
- Bolts: prepared the way the rotor maker says (new and threadlocked, for Magura and Zipp), tightened crosswise to its figure, and within the adapter maker's figure when they go into an adapter?
- Lockring: right type for the hub (by axle at the front, by model on a Shimano rear hub), at 40 N·m? DT Swiss warns that its adapter lockring must not be used to mount a Center Lock rotor: it won't tighten it properly and leaves excessive play.
- Alignment: Zipp says to check the rotor is centered in the caliper and, if not, follow your brake maker's instructions. Magura's MT A2 instructions say to check the rotor runs between the pads without touching, aligning the caliper if necessary.
- Follow-up: DT Swiss lists rechecking the adapter (40 N·m) and rotor screws (6 N·m) every 20 operating hours.
What to check on your own bike
- Hub or wheel: the "Brake type" row (Shimano hubs) or "Brake Compatibility" row (Zipp wheels) in its spec sheet.
- Front or rear, axle type and size and, on a Shimano rear hub, the model number: these decide the lockring.
- Rotor model, diameter and thickness: these decide the adapter, or rule one out.
- Brake caliper and pad type: these decide which Center Lock rotors are listed for you. For Shimano brakes, that's chart C-461.
- Torque: the rotor's instructions for the target; the adapter maker's figure as the limit when the bolts go into an adapter, the hub maker's when they go into a six-bolt hub.
What this page does not tell you
- Torque figures here are each maker's own, for its own parts. If the maker of your rotor, adapter or hub gives a different figure for its part, that figure applies.
- Shimano's spec handbook, compatibility charts and dealer's manual give no bolt torque for the SM-RTAD05 or for Shimano's six-bolt rotors. Follow the instructions that come with the rotor or adapter.
- TRP, HED, HUNT and Ritchey don't publish a list of rotors for their adapters, so a particular rotor can't be confirmed to fit them. Check your rotor maker's instructions, or confirm fit with the adapter maker.
- Shimano page numbers refer to Ver. 2.7 of the spec handbook and Ver 2.6 of the compatibility file, both dated Sep. 17, 2026. Shimano's links point to the latest edition, so page numbers can shift; the section and chart names will still find the right table.
- This page doesn't cover caliper mounts, caliper adapters, or the largest rotor your frame and fork accept. Check your frame, fork and brake makers' specifications for those.
Check it on your own equipment
These go to the makers and standards bodies this page draws on, so you can look up your exact model.
- Manufacturer specificationShimano 2026-2027 Spec. Handbook: Rotor (CENTER LOCK), Rotor (6-bolt) and Rotor Adapter tables
Center Lock rotor list with diameters, thickness, pad compatibility and lockring types (printed page 244, PDF page 247); six-bolt rotor list (printed 245, PDF 248); the SM-RTAD05's compatible rotors and axles (printed 249, PDF 252); hub tables showing each hub's 'Brake type'.
productinfo.shimano.com - Manufacturer specificationShimano Products compatibility Information: charts C-461 (rotors by caliper) and C-612 (lockrings by hub)
Ver 2.6, Sep. 17, 2026. Chart C-461, printed pages 59 to 62 (PDF pages 54 to 57), lists the rotors each Shimano caliper takes by diameter, with notes on resin-only rotors and narrow versus wide types. Chart C-612, printed page 63 (PDF page 58), shows which lockring type fits each front hub by axle and each rear hub by model, with the TL-FC36 note.
productinfo.shimano.com - Manufacturer specificationMagura assembly instructions: disc brake rotor
Magura's steps for six-bolt and eight-bolt rotors, Center Lock rotors and its Centerlock adapter: arrow direction, the crosswise bolt sequence, 6 N·m and 40 N·m, which Magura rotors the adapter accepts and which it never does, the original-parts rule, degreasing and bedding in.
magura.com - Official support pageShimano dealer's manual DM-MADBR01: Installing the disc brake rotor
Shimano's Center Lock rotor installation step: lockring torque 40 N·m, with TL-LR15 and an adjustable wrench for the internal spline type and TL-FC36 for the external spline type.
si.shimano.com
More questions
Sources
Every figure on this page comes from one of these 15 documents. Makers revise their specifications, so each is dated: open it before you buy.
- Disc Brake Rotor Removal & Installation | Park Tool www.parktool.com, Sep 23, 2026
- Zipp Road Wheels | SRAM docs.sram.com, Sep 23, 2026
- MAGURA Assembly instructions: Disc brake rotor (2600859 – 02-2025) magura.com, Sep 23, 2026
- MAGURA MT A2 user's instructions (0020165) magura.com, Sep 23, 2026
- 2026-2027 SPEC. HANDBOOK, Ver. 2.7, Sep. 17, 2026, SHIMANO INC. productinfo.shimano.com, Sep 23, 2026
- 2026-2027 Products compatibility Information, Ver 2.6, Sep. 17, 2026, SHIMANO INC. productinfo.shimano.com, Sep 23, 2026
- MADBR01 | Manuals & Technical Documents: Hydraulic Disc Brake (DM-MADBR01-08), Installing the disc brake rotor si.shimano.com, Sep 23, 2026
- DT Swiss HUBS - User Manual V2026.05 d2a13k6araex7u.cloudfront.net, Sep 23, 2026
- Center Lock Parts | DT Swiss www.dtswiss.com, Sep 23, 2026
- Wheel and Hub Specifications (GEN.0000000006258 Rev N, SRAM) www.sram.com, Sep 23, 2026
- TRP Cycling | Centerlock to 6-Bolt Adapter trpcycling.com, Sep 23, 2026
- TRP Six-Bolt to CenterLock Adapter Installation Guide (CenterLock Adapter Owners Manual - 28 JUL 2021) cdn.shopify.com, Sep 23, 2026
- 6-Bolt to Centerlock Adapter | Disc Rotor Adapter – HED Cycling Products hedcycling.com, Sep 23, 2026
- Hunt 6-Bolt Rotor Adapter – Hunt Bike Wheels US us.huntbikewheels.com, Sep 23, 2026
- Shop Centerlock-to-6-Bolt Rotor Adapter | Ritchey Logic ritcheylogic.com, Sep 23, 2026